<<Previous page

Description l Features l Options l Specification

Sprint 2000 HO is for the printing professional who needs an affordable and economical gas dryer capable of meeting extremely high production volumes. Sprint 2000 HO provides the power and performance to keep pace in the highest production environments. Available in LP or natural gas, Sprint 2000 HO combines a 390,000 BTU burner with three dedicated blowers to deliver remarkable temperature consistency and exceptional curing rates. The circulation blower forces heated air through the vector knife air plenum and across the belt, the power blower provides independent combustion air for the direct-fired burner, and the exhaust blower evacuates up to 2200 scfm. The resulting flame promotes fast, even, efficient curing. Sprint 2000 HO’s unitized forced air system quickly brings the heat chamber up to the desired temperature, and its unique industrial insulation layer keeps more heat in the chamber for consistent temperatures and cost-effective operation.

The combined result of Sprint 2000 HO’s heat source, blowers, and insulated chamber is uniform temperatures throughout the chamber. Sprint 2000’s high visibility tower light confirms that temperatures are within user-set parameters. Temperature readings outside those parameters will result in visible and audible alarms, while any anomaly in the control system will result in an audible alarm and automatic shutdown. Sprint 2000 HO’s solid-state control center features a fuzzy logic microprocessor in a rotating control panel atop the dryer for easy operator access. For convenience and safety, M&R includes System-Saver™ to allow blowers and belt to continue to run in cooldown mode after burner shutdown, then shut off automatically upon reaching the target cooldown temperature.

Sprint 2000 HO is available in four widths, and single-burner models come in five standard heat chamber lengths. Four-foot (1.22 m) conveyor extension sections and two-foot (61 cm) expansion heat chamber sections are also available. The ability to configure Sprint 2000 HO so many ways makes it tops in flexibility and the perfect textile dryer for any size operation. Sprint 2000 HO is also easy to operate and simple to maintain. Filters are easy to reach and clean, and lubrication points are conveniently located. Sprint 2000 HO is designed and built with M&R’s commitment to quality, durability, and design excellence, and is backed by M&R’s unsurpassed service and support.

Top of Page

• Aluminum conveyor rollers are large to promote positive belt tracking
• Driven by reliable heavy-duty DC motor
• Heat resistant, Teflon®-coated fiberglass belt
• Speed (minimum) of 3’ (91 cm) per minute
• Solid-state belt speed controller
• Solid-state digital belt speed readout for easy duplication of speed settings

• 48” (122 cm), 60” (152 cm), 72” (183 cm), and 84” (213 cm)

• 3 separate dedicated blowers (combustion, circulation & exhaust)
• AC frequency-controlled variable speed motor on circulation blower for flexibility
• Circuit breaker design allows easy reset and eliminates cartridge-type fuses
• High volume blower recirculates up to 80% of heated air
• Exhaust blower evacuates up to 2200 scfm @ 1¼4” (6 mm) static pressure (measured at the Exhaust Discharge Port) through 12” (30 cm) diameter exhaust duct
• Stainless steel filter slides out for easy cleaning

• AGA® & CGA® approved (design certified by the American and Canadian Gas Associations to meet or exceed national safety standards for design and performance)
• Panel listed by Underwriter’s Laboratories® (UL)

• Air-cooled cabinet assures long life for electrical components
• Approved gas controls
• Control panel rotates for easy access
• Fuzzy logic controller with ability to learn continually narrows temperature bandwidth until optimal range is reached
• Simultaneous digital display of process temperature and set temperature
• Solid-state design
• System-Saver™ allows blowers and belt to continue to run in cooldown mode after burner shutdown, then shut off automatically upon reaching programmed temperature
• Temperature status tower light indicating temperatures are within user-set tolerances is visible to operators around the entire dryer perimeter
• Temperature readings outside user-specified parameters result in visual and audible alarms

• Assembled and tested at M&R’s factory to assure easy installation
• Bearings are high speed, high temperature
• Designed for maximum thermal efficiency
• Entry/exit openings are adjustable
• Joining fasteners are specialized to simplify the connection of additional heat chamber units
• Low profile design
• Modular design for future expansion
• Rigid steel construction Exhaust Drawer/Creosote Catcher

• Direct-fired burner rated at 390,000 BTU
• Double wall construction
• Galvanized steel interior
• Heavy-duty thermal insulation
• LP or Natural Gas
• Modular gas train simplifies maintenance
• Plenum air knives are pressurized with overlapping vectors, providing consistently uniform temperatures throughout the drying chamber

• 24-hour hotline

• Access to M&R’s Training Center

• Two-year limited

Top of Page

• Conveyor extension sections available in 4’ (1.22 m) increments
• Split Belt

• CE Compliant (Built to specifications established by the European Committee for Standardization®)

• Single-Phase available

• Additional 24” (61 cm) sections available

Top of Page

*    If incoming voltage differs from the voltage(s) listed in this brochure, calculate amperage accordingly

**   Measured at the Exhaust Discharge Port

***  Weight applies to models with an 8’ (2.44 m) heat/expansion chamber

Top of page

<<Previous page

ScreenPrinting Products-SD
858.547.9997
Fax: 858.547.9998

7130 Miramar Road, Suite 400-B
San Diego, CA  92121

Contact Us: sales@screenprintingonline.com
www.screenprintingonline.com